Shop
Showing 181–189 of 319 results
-
Harmonic Balancer Installer
$76.92Part No: 38800
Harmonic Balancer Installer
$76.92The Harmonic Balancer Installer is used to properly install harmonic balancers or drive pulleys that are pressed on one or two groove pulleys on the crankshaft.
- Safely install most engine harmonic balancer and pulleys without damaging the balancers or crankshaft ends
- Contains twelve thread adapters to fit more applications than other brands.
- Metric and SAE bolts and adapters service most engines
- Black oxide finish to resist rust
- Sizes included: M10 x 1.5, M12 x 1.5, M12 x 1.75, M14 x 1.5, M14 x 2, M16 x 1.5, M16 x 2, 7/16 – 20, 1/2 – 20, 9/16 – 18, 5/8 – 18, 3/4 – 16
- Match the crank bolt to the correct insert if needed.
- Use with Cal Van 189 Harmonic Balancer Puller – Remover
UPC: 047084388006
Shipping weight: 3.55lbs38800 Harmonic Balancer Installer Flyer
Also available:
38500 – Master Harmonic Balancer & Pulley Installer
38700 – Long Reach Harmonic Balancer and Pulley Installer
38710 – Ford® EcoBoost Long Reach Harmonic Balancer InstallerQuick View -
Harmonic Balancer Puller
$30.80Part No: 189
Harmonic Balancer Puller
$30.80The Harmonic Balancer Puller is designed to pull balancers, vibration dampers, pulleys, and gears with tapped holes. The four slots in the yoke allows the tool to be used in both two- and three-hole applications.
- Fits most domestic and import vehicles
- Center screw designed with removable, floating swivel prevents damage to shaft ends
- Yoke is forged from high-grade, heat-treated alloy steel and zinc plated for long life
- Metric and SAE bolts included
UPC: 047084001899
Shipping Weight: 2.3lbsQuick View -
Harmonic Balancer Puller
$95.54Part No: 386
Harmonic Balancer Puller
$95.54Designed for removing damper pulleys in tight engine compartments, without removing the radiator. The kit contains the 3-jaw puller, four lengths of forcing rods, and a forcing screw with a 3/8″ square drive for ratchet use, and a 3/4″ hex for wrench or socket use.
- Applications:
- GM 2000 Generation III 4.8L, 5.3L, 5.7L, 6.0L and 8.1L V8s
- Cadillac 4.5, 4.6, and 4.9L V8s beginning in 1988
- Chevrolet trucks 2003 – later 4.2L, I6, 2004 – current 3.5L, I5 and 2005 – current 2.8L I4
- Chrysler engines 1990 – later, including 2.0L, 2.4L – 4s; plus 2.5L, 2.7L, 3.3L, 3.5L, and 3.8L V6s
- Ford 1995 – later V8 engines with 3 spoke pressed on damper
- Mitsubishi Eclipse 1995 – 1999 2.0L DOHC non-turbo
UPC: 047084003862
Shipping Weight: 2.9lbsQuick View - Applications:
-
Heater Hose Coupler Remover
$11.00Part No: 44100CV
Heater Hose Coupler Remover
$11.00The Heater Hose Coupler Remover is designed to remove broken heater hose couplers on most vehicles. Heater hose connectors made of plastic can become brittle and crumble or other materials may corrode or damage from the heat and vibration. This can cause leaks and engine overheating.
- Splines cut their way into broken heater hose couplers making for easy removal
- Once the spline has attached to the coupler, rotate it out with a 5/8” wrench or socket
UPC: 047084441008
Shipping weight: .25lbsQuick View -
Heavy Duty Circuit Tester
$21.22Part No: 70
Heavy Duty Circuit Tester
$21.22- Tests 6-, 12-, 24- volt AC or DC systems for open grounded or short circuits.
- 60″ 16-gauge wire with heavy-duty ground clip
- Two replacement indicator bulbs: Part #67-01
UPC: 047084000700
Shipping Weight: .45lbsAlso available:
78 LCD Test Light
80 Logic Light Circuit TesterQuick View -
Heavy Duty Pinch Off Pliers
$22.23Part No: 16500
Heavy Duty Pinch Off Pliers
$22.23- Eliminates the need to drain systems when servicing cooling systems.
- Pliers squeeze heater or radiator hoses shut and jaws swivel for parallel clamping.
- Automatic locking ratchet.
- May also be used to pinch off vacuum lines and fuel lines.
- For use on wire reinforced radiator hoses.
UPC: 047084165003
Shipping weight: 1.15lbsQuick View -
Heavy Duty Yoke Puller
$357.14Part No: 497CV
Heavy Duty Yoke Puller
$357.14Simplifies and expedites the removal of heavy-duty yokes on driveshafts, transmissions, and drive axles without damage to yokes or other components. Also, the caps are designed with flexibility in mind to service an extensive range of class 6-8 trucks.
- Fits on multiple Spicer full and half round yokes
- Fits on Meritor (Rockwell) RPL 20 & 25 series
- Manufactured from high grade steel
- Removal on yokes with bearing diameters between 1-7/8″ – 2-3/16″
UPC: 047084004975
Shipping Weight: 12.75lbsQuick View -
Heavy-Duty Battery Post & Terminal Cleaner
$11.34Part No: 553
Heavy-Duty Battery Post & Terminal Cleaner
$11.34This heavy-duty battery post and clamp cleaning brush is designed with tapered bristles to clean posts and terminal ends quickly and safely.
- Allows the user to quickly and safely clean posts and terminal
- Tapered bristles
- Comes with metal covering
UPC: 047084005538
Shipping Weight: .15lbQuick View -
Heavy-Duty Bearing Cup Installer
$181.32Part No: 20300CV
Heavy-Duty Bearing Cup Installer
$181.32Accurately install bearing cups in minutes into the Dana/Spicer SPL Life Series quick-disconnect u-joints. The press plate and specific adapters make proper installation easy every time while also reducing the risk of damage to the driveshaft, yokes, and joints.
- Three adapters to fit SPL 140, 170, 250 Series drivelines
- Use on quick disconnect universal joint only
- Safer alternative to makeshift methods
- Can be used with hand and air tools
- Great partner tool for Heavy Duty U-Joint Puller (Part No.199) and Heavy Duty Yoke Puller (Part No. 497)
- Applications:
- Dana®/Spicer® SPL 140, 170, and 250 Series U-joints found in class 6-8 commercial vehicles and equipment
UPC: 047084203002
Shipping weight: 12.5lbs20300CV Heavy Duty Bearing Cup Installer Instructions
Quick View
