CALL: 800-537-1077
INNOVATION, DEPENDABILITY, QUALITY SINCE 1939

Product Categories

Showing 13–24 of 272 results

  • U-Joint Puller

    $247.80

    Part No: 199

    U-Joint Puller

    $247.80

    199 – Heavy Duty U-Joint Puller

    A heavy duty solution for disassembling even the most seized stubborn U-joints in minutes on virtually all Class 7 and 8 trucks and machinery.

    Engineered for use with up to a 1″ impact tool.
    Eliminates dangerous vice and socket, or hammering removal methods.
    Does not damage the driveshaft, yokes, joints or bearing cups.
    One piece unit without bolts, cables, or assembly required.

    Out of stock

    Quick View
  • Hydraulic In-line Flaring Tool

    $221.29

    Part No: 166

    Hydraulic In-line Flaring Tool

    $221.29

    FEATURES

    Combines features of In-Line Flaring Tool and a Hydraulic Flare Tool to make a lightweight, low profile, affordable tool. Ease of use is highly increased compared to both hydraulic type and traditional. Timesaving aspects are offered because likelihood of bad quality flare where user has to perform operation again are highly unlikely. Fits into tight access areas allowing on car use. Does single, double and bubble flares. SAE: 3/16”, ¼”, 5/16”, 3/8”. Metric: 4.75mm, 6mm, 8mm. Includes Constant Tension Tube Cutter.

    Quick View
  • Relay Circuit Pro

    $200.74

    Part No: 76

    Relay Circuit Pro

    $200.74

    FEATURES

    • The 76 Relay Circuit Pro is a tool that can test an entire circuit from the battery to the component in question as well as determining if the relay itself is functioning properly. This tool gives the technician the ability to instantly determine the problem within a tested circuit. It will identify at the push of a button if a wire a part or a relay is defective without the use of a multi-meter. If the technician wishes to gain more information about the problem the tool also features easily accessible ports for use with other diagnostic tools. This tester also has other practical uses. Since the item can jump the relay the technician can use it as a remote control starter in engine work like compression testing distributor or cam shaft adjusting or to run the compressor during an A-C charge.
    • Kit includes the tester 6 popular relay leads 1 universal relay lead.
    • Comes in a blow molded case with a high density foam insert.
    • Works with both 12 and 24 volt systems.
    • Patent pending.
    Quick View
  • Metric In-line Dowel Pin Puller Set

    $194.09

    Part No: 95300

    Metric In-line Dowel Pin Puller Set

    $194.09

    FEATURES

    • New Dowel Pin Puller that extracts Dowels without the use of a slide hammer.
    • Fit the appropriate sized collet over the dowel tighten the sleeve Use outer sleeve and nut to extract the dowel.
    • Can be used with air ratchet or traditional ratchet.
    • Elimination of the slide hammer saves cost as well as effort and potential hand injury.
    • SAE Set includes 316, 14, 516, 38, and 12
    • Metric Set Includes 4, 5, 6, 8, 10, and 12mm
    • Master Set includes both SAE and Metric Collets
    • Patent pending.
    • 95200 In-Line Dowel Pin Puller SAE
    • 95300 In-Line Dowel Pin Puller Metric
    • 95400 In-Line Dowel Pin Puller Master Set
    Quick View
  • Ball Joint Removal and Installation Set

    $193.89

    Part No: 196

    Ball Joint Removal and Installation Set

    $193.89

    FEATURES

    • Removes and installs press-fit parts such as ball joints universal joints and truck brake anchor pins.
    • Contains: 3 receiver tubes (234” I.D. x 3″ O.D., 214” I.D. x 212” O.D., and 134” I.D. x 2″ O.D.)
    • Installation and removing adapters: 1 installing cup 1 receiving cup 1 installing adapter.
    Quick View
  • SAE In-line Dowel Pin Puller Set

    $187.88

    Part No: 95200

    SAE In-line Dowel Pin Puller Set

    $187.88

    FEATURES

    • New Dowel Pin Puller that extracts Dowels without the use of a slide hammer.
    • Fit the appropriate sized collet over the dowel tighten the sleeve Use outer sleeve and nut to extract the dowel.
    • Can be used with air ratchet or traditional ratchet.
    • Elimination of the slide hammer saves cost as well as effort and potential hand injury.
    • SAE Set includes 316 14 516 38 and 12
    • Metric Set Includes 4 5 6 8 10 and 12MM
    • Master Set includes both SAE and Metric Collets
    • Patent pending.
    • 95200 In-Line Dowel Pin Puller SAE
    • 95300 In-Line Dowel Pin Puller Metric
    • 95400 In-Line Dowel Pin Puller Master Set
    Quick View
  • The Front End Service Kit

    $180.18

    Part No: 185

    The Front End Service Kit

    $180.18

    FEATURES

    • The Front End Service Kit Includes five tools used in the servicing of ball joints pitman arms and tie rods on most vehicles.
    • A large and small Pitman arm puller for ball Joint applications.
    • Three different tie rod pullers.
    • Two ball joint separators.
    • Comes in a sturdy blow molded case
    Quick View
  • Bearing Splitter-Large

    $177.01

    Part No: 511

    Bearing Splitter-Large

    $177.01

    • Designed to remove and pull bearings in tight areas
    • Capacity 4″ to 6″
    • Removes thin faced & cone shape gears, with a beveled edge that can be easily placed behind part to secure gripping surface
    • Split and separate bearings where puller jaws cannot be used
    • Made from industrial strength steel

    Quick View
  • 7-Ton Bar Type Puller Bearing Separator Set

    $174.92

    Part No: 501

    7-Ton Bar Type Puller Bearing Separator Set

    $174.92

    FEATURES

    • Includes a Bearing Splitter with 4″ capacity two sets of hex push puller legs a 8″ bar type puller head mated with a custom thread forcing screw.
    • Professionals have a Puller-Bearing set for hard jobs up to 7-tons larger applications and greater reach 8″ to 16″.
    Quick View
  • Master Line Disconnect Tool Set

    $174.23

    Part No: 683

    Master Line Disconnect Tool Set

    $174.23

    FEATURES

    • The most complete disconnect set on the market.
    • Comes in a heavy duty case for easy access and easy storage.
    • No more random disconnect tools laying around to be lost all your disconnect needs in one place.
    Quick View
  • Two & Three Jaw Combination Pullers

    $172.79

    Part No: 954

    Two & Three Jaw Combination Pullers

    $172.79

    FEATURES

    • These versatile Combination Pullers may be converted into either a 2 or 3 jaw puller simply by changing the jaws on the yoke. All pullers have standard threads contrasting zinc and black oxide finish. Yoke and jaws are forged. All parts are heat-treated.
    • Two & Three Jaw Combination Puller 9in Adjustable, 11in spread, Center Screw 1116in – 18 x 838in, 7 Ton
    Quick View
  • 9-Way Slide Hammer Puller Set

    $168.49

    Part No: 956

    9-Way Slide Hammer Puller Set

    $168.49

    FEATURES

    • Pulls flange-type rear axles and most front-wheel drive hubs. Internal and external jaws provide a variety of combinations to pull bearings gears and seals. Two- and three-way cross blocks and cone provide the perfect jaw configuration for most jobs. Set also includes a grip wrench adapter and a dent puller attachment for sheet metal or other unique pulling requirements. Packaged in durable case.
    Quick View